Allnic M-3000 KT-120
Allnic M-3000 KT-120
Allnic M-3000 KT-120

Allnic M-3000 KT-120

€14,900.00
VAT included

FINANCIA TU COMPRA

A partir de €28.00 de compra

Inmediato y sin papeleos

Allnic M-3000 KT-120. Mono Power Amplifier.

Quantity
In Stock

  • Política de seguridad (editar con el módulo Información de seguridad y confianza para el cliente) Política de seguridad (editar con el módulo Información de seguridad y confianza para el cliente)
  • Política de envío (editar con el módulo Información de seguridad y confianza para el cliente) Política de envío (editar con el módulo Información de seguridad y confianza para el cliente)
  • Política de devolución (editar con el módulo Información de seguridad y confianza para el cliente) Política de devolución (editar con el módulo Información de seguridad y confianza para el cliente)

PRINCIPAL FEATURES

"Full Engagement" Output Transformers

Conventional output transformers use pre-set secondary windings to accommodate 4, 8 and 16 ohm loudspeaker loads. However, these conventional transformers utilizeonly one secondary winding at a time, while the other secondary windings remain "idle".
This approach has two adverse effects. First, the output transformers are not working at their maximum efficiency, reducing their output relative to their potential.
Second, the "idle" windings are not actually "idle" they are subject to parasitic
oscillations, producing their own "signal". This undesirable electrical information is
additive to the transformer's output, distorting the amplified signal going to the loudspeaker.
Allnic's "Full Engagement" transformers address these issues by having 4 independent, secondary windings which are always fully connected, never "idled".

This means that all secondary windings are always connected to your loudspeakers, regardless of which output switch position you use (4 ohms or 8 ohms or 8 ohms or 16 ohms, depending on the factory configuration you have selected). The result is that there is neithera loss of transformer output efficiency, nor the introduction into the output signal of distortion from parasitic oscillations of the secondary windings.

Large Nickel/FeSi Core Output Transformers

As with our other models, Allnic uses very large output transformers (114 mm) with nickel,mixed with FeSi, cores. This provides for higher inductance with fewer windings than other designs can provide and results in the great benefit of an extremely wide range of outputfrequencies.

Powerful Driving Circuitry

Allnic belives in the importance of using high-quality, low noise and powerful driving circuitry n all its amplifying devices. Therefore, in the M-3000, we employ the E282F tube in triode mode as the second stage driver tube, with a load of about 5 K ohm, and using 20mA of current.

The listener can easily hear and even "feel" the differences between this design and other, more conventional, ones.
Please compare, in your imagine, it to conventional 12AU7 or 12BH7's driving force, 47K ohm loaded. 2 ~ 3mA current.

"Soft-start" Circuitry

Allnic uses soft start circuitry that, after sufficient warm-up only, provides the high voltage supply to the plate of each tube. This protective design results in prolonged tube life and fewer and less frequent issues with tube performance.

"Easy-lift" All Aluminum Chassis

The M-3000 chassis has a new handle design for easy-lifting and is all aluminum, milled precisely in a sophisticated maching facility.

 Analogue Power Tube Current Monitors

In order to provide constant current (bias) monitoring for the power tubes, Allnic uses a separate analogue current meter for each tube. The meters make it exceptionally easy to see the status of each tube at any time and to respond immediately to any variation in bias by use of the bias control knob for the relevant tube. The meters offer a simple, unambiguous indication of each tube's status compared to cinventional LED bias monitors.

"On-the-Fly" Triode/Pentode Switching

Switching between triode and pentode operation can be done "on-the-fly" at any time while the amp lifier is in use.

SPECIFICATIONS

  • Output Power : 140w (8Ω load, at 1KHz)
  • Distortion : 0.17% at 1KHz, 10W
  • Frequency Response : 20Hz - 20KHz  Flat
  • S/N Ratio : -80dB(CCIR, 1KHz)
  • Damping Factor : 8 at 8Ω load at 1KHz
  • Voltage gain : +24dB
  • Input Impedance : 100KΩ(unbalanced)
  • Input Sensitivity : 2V for rated power
  • Tubes : KT-120 X 4, E282F X 2, 6AK6 X 1, Per Channel
  • Dimensions : 430mm X 430mm X 240mm(W.D.H)
  • Weight : 40Kg net.

2311100008

16 other products in the same category:

special ofers for subscribers

You may unsubscribe at any moment. For that purpose, please find our contact info in the legal notice.

Free delivery

Nam liber tempor cum soluta nobis elefend option congue nihil imperdiet.

money guarantee

Nam liber tempor cum soluta nobis elefend option congue nihil imperdiet.

online support

Nam liber tempor cum soluta nobis elefend option congue nihil imperdiet.

SELECT id_product FROM ps_product WHERE id_product > 4699 ORDER BY id_product ASC LIMIT 0,5